RSS

Author Archives: Admin

Roll Or Spray Paint Your Home Walls?


When planning to paint your home walls, the first question that pops your mind is whether to go for sprayer or roller. It’s a difficult decision. Spray painting seems to be faster, but there involves extensive preparation work. In comparison rolling seems slower, but you get better results due to quality coat.

So if you are looking for quality of the painted surface, you would find the rolling paint option a better idea to go with. With roller painting, you get a thicker paint layer and better colour consistency than with spraying. Before you finally reach on some decision, you also need to consider cost, surface condition and preparation time.

Spray Paint Great For Texture

Spray painting is fast and are good for certain jobs. You may wish to use a paint sprayer if your wall lots of detail work or texture. Spraying is good for complicated textures. Also, paint sprayers have the ability to work into the narrowest crannies, laying down a thin coat.

Restore your building exterior with curtain wall spraying service.

Simple Method

If you don’t want to keep things from getting complicated, roller is the way out. For this method all you need is roller, roller cover, paint tray and tray liner. With rolling option you can paint for some time and then give a break to attend your life. While with spray option, you have to continuously give time to it and it consumes your entire day.

No Money Wastage

Tool required for spray paint that is paint sprayer is costly, and it requires maintenance as well. You waste a lot of paint while paint spraying as the atomized paints drifts away. To be precise one-third of the sprayed paint does not end up on the wall surface. When you use rolling method, almost every drop ends up on the surface.

Reduce Masking Work

When opting for rolling paint method, you need to mask out only a few areas, on the other hand while spray painting a lot of area needs to be covered. Every square inch of the area that you don’t want to get painted must be masked in film or with a drop cloth. If you don’t mask the area you don’t want to get painted, then even that would be painted.

Not Painting Ceiling

If you are not planning to paint the ceiling, then paint-rolling is the best way out. When you opt for paint rolling, you can easily exclude the ceiling. Also, you don’t need to mask the ceiling when rolling walls.

When The Surface Is Not Clean

Sometimes it’s not possible to thoroughly clean the surface. Paint rolling is the clearly the option then. Rolled paint can easily hide the initial coat as it is thick. And it bonds better to the surface. While spray painting, the tiny paint droplets produced do not connect with each other so well. Professional painters use a fusion technique that uses the best of spraying and rolling: back-rolling. Paint is sprayed on the wall then is immediately rolled down, fusing the droplets together.

Advertisements
 
Leave a comment

Posted by on May 14, 2018 in Refurbishment

 

Tags:

How to Keep Glass in Your Office Sparkling Clean?


Maintaining an office, in terms of keeping it clean is a major task. Office buildings or commercial spaces are designed such that they use glass in most places and in most possible ways. Be it windows, doors, room dividers and even table tops, glass adds an ultra modern look to the office. Glass has other benefits like the place look spacious, sharp, clean and gives complete visibility.

We have used the word clean but keeping the glass of the entire office building clean is a daunting task. Glass gets dirty very easily. Even the tiniest mark on a huge pane of glass is very much visible. So keeping the appearance of glass crystal clear mostly requires commercial cleaning services. And if the glass got damaged then glass repair service needs to be pitched in.

Regular cleaning is essential to keep the glass in your office building clean, clear and looking like new for longer. In case of building refurbishment, you can bank on ARS Ltd. Here are a few tips to keep the glass sparkling clean:

1. The first and foremost way to keep the glass in your office spotless is to clean it from top to bottom. This way you can keep away from streaks, so always prefer cleaning of glass should be done from top to bottom.

2. If you are the one who prefer using old newspaper or paper towels when cleaning glass then immediately stop using them as they can leave lint and streaks. Also, the process is time consuming. Instead use a squeegee that gets the work done faster. A microfibre cloth can also be used.

3. You need to take care of the type of water your cleaners are using. Ask them to not use hard water as it leaves permanent marks that make the glass look cloudy. Over the time, the glass surface looks shabby so better to tell the cleaning company to use soft water.

4. Try to get your windows clean on a cloudy day. The reason being on a sunny day, the window gets easily dry leaving streaks and spots.

5. To avoid dirty hands leaving marks on glass doors, install handles on the doors. You could also opt for automatic door openers.

6. Marks and scratches on the glass can be taken care of by making your glass bump-proof. To ensure that people don’t bump into the glass by placing frosting, decorative window tinting, or etching on clear glass. Protective tape and decorative glass stickers too can be used. Also using a sticker let people know to watch out for the glass. Get in touch with ARS Ltd. for any kind of building glass repair service.

7. Ensure that your cleaner instantly wipe off any substances or liquids that stick to the surface of the glass. If you don’t wipe it off at that time, it will leave marks. These were the tips to keep glass in your office sparkling clean.

 
Leave a comment

Posted by on December 30, 2017 in Refurbishment

 

Tags:

4 Tips for Protecting Your Roof This Winter


Winters are approaching. Some of you will be happy as this magical time of the year is around the corner. But some others might be in great tension. The worries and the tensions stem from the fact that you are not completely prepared for the winter. More than you it is your house that needs to prepare itself for the upcoming winters. Building maintenance is very crucial in this season. Weather conditions in the winter season are quite unpredictable.

Roof

Sometimes it is rainy, other times you have frost and some other day you can have immense snowfall. The major part that bears the brunt of this harsh season is the roof of your house. In this article we’ll tell you about some tips to protect the roof of your house.

Remove the ice and snow regularly from the roof

You might say that the snow deposition on the roof of your house looks amazing and presents a picturesque view. But if kept for long, the excessive deposition of the snow on the roof can cause huge damage to it. It can also result in the partial or the complete collapse of the roof structure. Building maintenance experts also suggest that you should keep removing the snow once in a while from the rooftop. The basic reason behind the collapse is the increasing weight on the top of the roof with the continuous deposition of the snow.

Check that the insulation is proper

You must have heard of the problem of building of the ice dams. This problem occurs when the insulation of the roof of the house is improper. If the rooftop is too warm, then the snow will melt and the water will flow down the drain pipes and refreeze there causing blockages. It can even freeze in the gutter system and cause blockages which may require you to spend huge amount of money in the building maintenance.

Check if there are any broken tiles or bricks

One or two damaged tiles or brocks in the roof structure may seem to be quite obvious and not to worry types in the spring or summer season. But the same can be a challenging problem for you to deal with if the season is winter. These missing tiles will further enhance the problems of the leakage if the snow keeps on accumulating on the rooftop. You should call the building maintenance personnel and ask them to repair and rectify these minor issues which can pose a bigger problem later on.

Keep the guttering system clear

It is suggested that you regularly undertake the cleaning of the guttering system of your house. The leaves and the other clutter shall be cleaned regularly so that it poses no bigger problem in the winter months. If you do not do this then snow and ice can get clogged with the clutter and the drainage system will run into problems.

Keep the above-mentioned points in mind as you prepare your home for the upcoming winters.

 
Leave a comment

Posted by on November 28, 2017 in Refurbishment

 

Tags:

Know How to Protect Curtain Walls during Construction


Large commercial buildings come with glass curtain walls. This means that one wall of the building is completely made of glass. The greatest benefit of such walls is that they allow abundant light to come into the building interiors, without allowing dirt and dust from making entry into the structure. Many people might not know but these glass curtain walls are actually attached to the outer structure of the buildings. Glass curtain walls extend through the whole building and are encased in metal framing for making them strong. Standing in front of the glass wall, you can enjoy complete outside view without any kinds of obstacles.

However, there are instances where the glass curtain walls are damaged during some kind of construction work. Damage can be inflicted on curtain walls during shipment to the main job site. Some walls also develop scratches etc during the process of installation. Post installation too, problems might arise when the other construction works take place and cause damage to the curtain walls. It is recommended to take proper protection so that these walls don’t incur any kind of damage or distress. For the aluminum casings, foam strips or reinforced cardboards are used so that they can be packed properly and saved from damage. The wall glass is protected with adhesive window films. This helps in providing protection from scratches etc.

With proper care and protection, the curtain walls might reach the job site well and even be installed without a single scratch or problem. But after this, utmost care has to be taken so that no damage is inflicted on the glass curtain walls. There are construction projects which continue for years and work is done in the interiors as well as in the exteriors. In such circumstances, it is quite possible that the wall might face breakage, scratch etc.

The glasses that are used for commercial buildings’ curtain glass walls vary in quality from one another. While some of the glasses might be ordinary, some of them are quite expensive. Areas which are prone to hurricanes, typhoons and earthquakes usually use the expensive varieties of glass curtain walls. These glasses are resistant to seismic vibrations pr hurricane and typhoon impact and do not break or collapse down. There are many commercial buildings where high security and confidential works are done. For such buildings ballistic proof glass is recommended to be used for additional safety and security.

Protection of glass walls during the construction work

If you notice closely, you will find that majority of damage on curtain walls takes place at the bottom 5 feet or so. This is because maximum contact takes place with the wall in this height. One of the best ways of protecting the glass wall is by placing a wall of cardboard or other materials in front of the glass wall. Wooden or plastic walls can also be used for additional protection. Corrugated plastic or corrugated cardboard are the best options as they are lightweight, inexpensive as well as readily available. It is even better if these are white in color so that they are visible at night time too.

With more and more commercial buildings coming up with curtain walls, contractors have devised ways and means for maintaining and repairing them. Special equipments and devices are available for building glass repair and glass spraying. If the glass windows develop scratches, glass scratch removal system can be used for getting rid of the ugly scratches.

 
Leave a comment

Posted by on August 29, 2017 in Glass Repair

 

Tags:

11 Tips on Finding The Right Home Improvement Contractor


Home remodeling or home improvement projects need to be handled by professionals as there are innumerable things that need to be taken care of. Whether you are looking for complete building refurbishment or partial renovation of a home, you need to get in touch with a home improvement contractor for the same.

Mentioned below are 11 effective tips for selecting the right contractor:

  • Understanding the credentials of the contractor is very important. Check his certifications and qualifications and understand whether he will be able to handle the job well or not. Along with certifications from some recognized organization, the contractor should be licensed, insured and bonded at the same time.

 

  • The contractor should have good communication skills so that talking to him become simple and easy. The contractor should understand your requirements and expectations and you should be able to understand what he says for the project. Try keeping regular contact via phone, chat or email – which is convenient for both the parties.

 

  • Be specific and upfront with the budget in which you are planning to work. The contractor should have clear idea regarding the budget and should work accordingly. If required, the work can be done in phases. Refrain from hiring a contractor who does not understand the importance of following a budget.

 

  • Ask the contractor for his suggestions regarding the home improvement project including a list of materials that will be needed for the same. People make a mistake by hiring contractors with the lowest budgets but they turn to be great failures on the long run. Look for moderate contractors who understand the work well and charge reasonably too.

 

  • The contractor you hire should know about all the rules and regulations that need to be followed for the home improvement project. There might be need of some applications and permit obtaining works and the contractor should be able to handle all these. You should have knowledge regarding the same so that you can cross-question him and see if all is running fine.

 

  • The contract for the home improvement project should be in writing and it should contain minute details like project description, payment arrangements, time frame of the work, total cost that might be incurred, contractor’s license number, phone numbers of people working on the project etc. If timeframe is not mentioned, refrain from signing the contract as this means that the contractor has other projects running and this one might be neglected.

 

  • Before starting the demolition work, the contractor must ensure that all the supplies and new equipments are in place. Without the arrangements already made and done, the contractor will not be able to work freely.

 

  • Home renovation is not as easy as it seems. A good and reliable contractor should assure that the project will be done in the best manner and be there to manage things. He should be able to help the home owner in being prepared for the process of home improvement and renovation.

 

  • Make sure that you check references of the contractor from some trusted and reliable sources. If most of the references and reviews are positive, you can definitely go with the contractor; otherwise look for better options. There are aplenty available online.

 

  • Insurance coverage for renovation projects is must. Verify the insurance coverage and understand what is covered in the homeowners insurance and what coverage is provided by contractor’s business insurance. Having a copy of the company’s insurance policy is mandatory.

 

  • Be careful of the payments that are being made. Collect bills and receipts for the products that are being bought for the project. Also while making payments to the contractor have a receipt signed so that there is no confusion later.

Keep these contractor hiring tips in mind and make your home renovation project grand success!

 
Leave a comment

Posted by on June 28, 2017 in Refurbishment

 

Top 5 Cleaning Tips from the Pros


Whether it is your home or your office, keeping it clean, prim and proper is absolutely important. This is required for healthy staying. There are some basic cleaning tactics and techniques that all of us know. Years of experience come into count for sure. But there are certain cleaning aspects, which seem pretty difficult and time taking. For such cases, there is no other alternative than seeking assistance from professionals. These professionals have highly effective building cleaning tips and tricks up their sleeves, so that the cleaning work can be done in the most efficient manner within the shortest span of time.

Mentioned below are 5 highly effective cleaning tips from the pros for cleaning up building parts:

Quick dusting tip

Dust and dirt buildup is common in all homes and office buildings. Offices and homes that are located by roadsides are more prone to dirt and dust. Regular dusting should be done in these areas to keep dust away from accumulating on various things in the house. Usually soft cloths are used for the purpose of dusting as they tend to remove dust and dirt well. But professionals opine that feather duster is a better option for getting rid of dirt and dust from home. And there is valid reason for the same too. These dusters can easily clean dust from the chandeliers or even from the crevices of the blinds successfully. Working with these dusters is also highly convenient as it helps in getting the cleaning done quickly.

Removal of soap scum made easy

We all have struggled with removing soap scum at some point of time in our life. But the cleaning pros know some extremely easy and convenient way of getting rid of the same. Instead of using a sponge for removing soap scum, try using a plastic putty knife for handling soap scum. You will notice that soap scum will be removed in half the time and the efforts required will also be lot less. For avoiding buildup of soap scum, try using synthetic soaps and liquid soap gels instead of bar soaps.

Make vacuuming less time consuming

Vacuuming takes lot of time because we generally have to unplug and plug the cleaner again and again for moving the machine in different rooms. Within this time, the whole process of vacuuming could have been completed. You don’t have to do much for the same. Just buy an extension cord and use the machine in different rooms without the need for plugging and unplugging the same repeatedly. This will let you do more work in less time.

Use squeegee for making windows streak resistant

Streaks on windows are common, how much ever you clean them properly. The only solution to this problem is by using a squeegee for window cleaning. Many people try cleaning windows with newspapers for the slight soda content in them or with paper towels for their softness. But these are not that effective in removing the streaks. Invest in squeegees for cleaning window streaks completely – large ones for large windows and small ones for small windows.

Shining stainless steel

Stainless steel is used in various ways in offices and in homes. They are scratch and stain resistant; but they are prone to attracting stickiness and show fingerprints. Wiping stainless steel surfaces with mineral oil is a great way of keeping the surface shining. The problem of stickiness can be dealt with this process successfully and future cleaning time will also be minimized.

Follow these steps and clean like a pro!

 
Leave a comment

Posted by on May 29, 2017 in Refurbishment

 

Tags:

Top 10 Tips to Improve Surface Finish


Whether you are working on a wall or on some mechanical equipment part, it is important that the surface of the material has a smooth finish. Rugged and scratchy surfaces might cause injury to the hands or other parts that come in contact with the surface.

Mentioned below are some excellent tips shared by ARS Ltd., which help in improving surface finish in a great manner:

1. Minimize the feed – Minimizing the inch per revolution (IPR) will help in reducing flank wear and also enhances insert life. While roughing, it is recommended to use tools, which are capable of generating high feed. But while finishing, the feed should be reduced for improving surface finish.

2. Increase the speed – Increasing surface feet per minute will help in reducing build up edge. Tool life is prolonged with this step and chances of damage to the tool parts are also reduced.

3. Use of chip breaker is good – Using chip breakers help in reducing cutting pressures. The chips that are produced as a result can be evacuated conveniently. There are materials in which stringy and long chips produced. With a chip breaker, it is possible to produce smaller chips so that they get out of the cutting zone quickly.

4. The top rake angle should be increased – Rake angle is considered as a variable in the insert’s design. And this angle can be used for achieving the best surface finish. Having a lead angle will make the insert into the material easy and smooth and hence a smooth finishing can be obtained on the surface.

5. Using a wiper helps – Using an insert with a wiper is a recommendation given by experts when surface finishing needs to be smooth and good. Along with having a smooth surface, the insert with the wiper also helps in increasing feed rates.

6. A large nose radius helps – Surface finishing is directly related to the size of the nose radius of the insert. Smaller nose radiuses put lesser pressure on the tool, but there are also limitations on the feed rate, which can be used. With a larger nose radius heavier cut can be made, which is important when hard-to-cut materials are cut.

7. Using different tools to rough and finish – It is recommended to use different tools for roughing and finishing. Generally the roughing is done by slightly used insert; while finishing is done with a new insert altogether. Talking of the insert material, cermet insert is the best option in this regard.

8. Using the correct technique for getting perfect finishing – For fine and smooth surface finishes, it is important to apply the right techniques. It is recommended to select a cutter, which is smaller than the main radius. The cutter can be programmed for smooth finishing from line to line.

9. Checking the workholding and toolholding – Improper fixturing and toolholding will lead to chatter. Also a machine tool which is not rigid will cause various problems. Stable and rigid workholding is the main key for smooth surface finishing.

10. Using the coolant as per need – Usually there is lot of confusion regarding the fact whether coolant can be used or not for improving surface finish. The use of coolant will depend upon the kind of operation, which is being performed and also on the material for which surface finishing is being done.

 
Leave a comment

Posted by on May 1, 2017 in Refurbishment

 
 
%d bloggers like this: